Avoiding Mold: Areas You Need to Pay Attention to

Areas Commonly Infested with Mold

mold area 2Mold can begin to form in areas that usually get moist, specifically on dark areas without proper ventilation. Moreover, this is a common problem in homes that are affected by a flood, and you may notice molds accumulating in your basement walls or ceilings, as well as behind drywalls. There are other places in your home where mold can show up too, and you may not even notice these right away, until it becomes much more difficult for you to remove.

With this in mind, it helps to be aware of the typical places at home or elsewhere that may become infested with mold. By doing so, you can address the issue right away before it gets worse.

1. The Door of Front-Loading Washing Machines

If you look closely, you are most likely to spot mold growing around the gasket, which is on the door of your washing machine. Front-loading machines are more prone to molds because the door remains closed after use. Since the area is still wet, keeping it closed can cause mold to remain inside and multiply. To solve this problem, make sure you use a dry cloth to wipe the glass material and gasket frequently, to prevent mold from accumulating inside. Another effective way to get rid of mold is by putting some chlorine bleach mixed with hot water inside the tub and just running it for a few minutes.

2. Air Conditioning System

mold area 1

Another favorite breeding ground for mold is your AC unit, as pollen and dust usually hang around, plus the fact that the area remains moist all the time. The issue can get even worse during warm months when you do not use the unit for at least 24 hours, as humidity gets into the unit and stimulates growth of mold on the coils, drain pan and the ducts. So, if this is an issue that affects the central AC unit, you should contact a professional who can remove mold from the area by having it cleaned. In case you own a window-type AC unit, you can simply use a HEPA filter vacuum to clean the blower and rinse the coils and drain pan with equal parts of water and bleach. Running the unit for a minimum of 10 minutes every day, also helps to allow air circulation and maintain the humidity level inside the house at below 55 percent.

3. Chimneys

As mentioned previously, mold grows in areas where there is a good amount of dirt and water present. Since brick crevices are susceptible to moisture, then you can expect mold to accumulate in these sections in your chimney. It is also an issue with rusty chimney caps as snow and rain just get in quickly. To address this problem, have the flashing fixed and replace any rusty or damaged chimney caps. It is also important that you contact a chimney sweep to have the mold removed and ensure it functions properly without creosote forming in it.

4. Dishes

As disturbing as it may seem, mold may also grow on dishes, particularly when they are stacked together while still wet or moist. You may notice mold along the edges and back portion of your plates over time. The quickest way to get rid of mold is by washing the dishes again and drying them. Then, use a cloth soaked with vinegar to wipe the cabinets before placing your dishes back in them.

5. Window Sills

mold area window

Since mold feeds on dust and dirt and these form whenever an area is moist, then you can expect window sills and sashes to be favorite mold spots. You can prevent or remove the mold by wiping moisture that collects from under the window sills and sashes. There may also be a need to have the window sashes replaced in some cases, to stop condensation that causes mold.

6. Drip Pans on Your Fridge

Lastly, mold often appears in the drip pans right underneath the fridge. Food and moisture often get into this area, so mold may end up growing and accumulating. Thus, make it a part of your annual task to clean the drip pans using a cup of water mixed with a teaspoon of hydrogen peroxide. Next, wipe the area with a rag or cloth soaked in vinegar to prevent mold from reappearing.

So, inspect these areas, keep them clean, and you will finally end your problems with mold getting into your home.

Resource:

http://www.cdc.gov/mold/faqs.htm

http://www.medicinenet.com/mold_exposure/article.htm

http://www.epa.gov/mold/moldguide.html

https://en.wikipedia.org/wiki/Mold

Spread the love

Leave a Reply

Your email address will not be published. Required fields are marked *